新聞中心

S3C2440-IIC

作者： 時間：2016-12-02 來源：網絡 收藏
void __irq IIC_ISR(void){
rSRCPND |= 0x1＜＜27;
rINTPND |= 0x1＜＜27;
flag = 0;
}
void wrat24c02(unsigned char add,unsigned char word, U32 length){
int i;
flag = 1;
rIICDS = 0xa0; //dev add
rIICCON &= "(0x1＜＜4); //清中斷
rIICSTAT = 0xf0; //主發送模式，寫開始信號輸出，IIC Rx/Tx使能
//等待ACK，接收器在接受到8位數據后，在第9個時鐘周期，拉低SDA電平，然后會產生中斷
while(flag == 1)
delay(100);
flag = 1;
rIICDS = word; //word add 發送要寫入的數據的內存其實地址
rIICCON &= "(0x1＜＜4);
while(flag)
delay(100); //注意要有delay
for(i = 0; i ＜ length; i++){
flag = 1;
rIICDS = iic_buffer[ i];
rIICCON &= "(0x1＜＜4);
while(flag)
delay(100);
}
rIICCON = 0xe0; //IIC應答有效，IICCLK=fpclk/512,IIC接受發送中斷使能位
rIICSTAT = 0xd0; //主發送模式，rIICCON和rIICSTAT配置好，方便下次使用
}
void rdat24c02(unsigned char add, unsigned char word, U32 length){
int i;
char temp;
flag = 1;
rIICDS = add; //dev add
rIICCON &= "(0x1＜＜4);
rIICSTAT = 0xf0;
while(flag)
delay(100);
flag = 1;
rIICDS = word; //word add
rIICCON &= "(0x1＜＜4);
while(flag)
delay(100);
flag = 1;
//這里的IIC的隨機讀操作，根據IIC的隨機讀時序，先發啟動，要讀取的設備地址和寫的內存地址，方向是寫,即0，重啟IIC，
//發要讀取的設備地址，這次方向是讀，然后接到ACK，從機向主機發data，主機相應ACK，直到最后一個data，主機不相應ACK，
//發送停止信號
rIICDS = add; //dev add
rIICSTAT = 0xb0; //改變方向?yàn)橹鹘邮?div> rIICCON &= "(0x1＜＜4);
while(flag)
delay(100);
flag = 1;
temp = rIICDS;
rIICCON &= "(0x1＜＜4);
while(flag)
delay(100);
for(i = 0; i ＜ length; i++){
flag = 1;
if(i == (length - 1)){
rIICCON &= "(0x1＜＜7);
}
iic_buffer[ i] = rIICDS;
rIICCON &= "(0x1＜＜4);
while(flag)
delay(100);
}
rIICCON = 0xd0;
rIICSTAT = 0x90;
delay(200);
}
int Main(){
int i;
count= 0;
length = 0;
cmd = 0;
command = 0;
rGPECON = 0xa0000000; //GPE15～14 IICSDA，IICSCL
rGPEUP = 0xc000;
rIICCON = 0xe0; //IIC應答有效，IICCLK=fpclk/512,IIC接受發送中斷使能位
rIICSTAT = 0x10; //IIC總線有效Rx/Tx
rULCON0 = 0x3;
rUCON0 = (1＜＜11)|(1＜＜2)|(1＜＜0);
rUBRDIV0 = 26;
rSRCPND = (0x1＜＜28)|(0x1＜＜27);
rINTPND = (0x1＜＜28)|(0x1＜＜27);
rSUBSRCPND = 0x1＜＜0;
rINTMSK &= "((0x1＜＜28)|(0x1＜＜27));
rINTSUBMSK &= "(0x1＜＜0);
pISR_UART0 = (U32)UART0_ISR;
pISR_IIC = (U32)IIC_ISR;
for(i = 0; i ＜ 8; i++){
iic_buffer[ i] = 0xee;
}
while(1){
switch(cmd){
case 0x01:
cmd = 0;
wrat24c02(add, word, length);
break;
case 0x02:
cmd = 0;
rdat24c02(add, word, length);
for(i = 0; i ＜ 8; i++){
while(!(rUTRSTAT0&0x4));
rUTXH0 = iic_buffer[ i];
}
break;
}
}
return 0;
}
上一頁 1 2 下一頁

關鍵詞： S3C2440IIC串行總

評論


技術專區

關閉