TQ2440啟動代碼分析（二）

;先通過mrs 指令將狀態寄存器值讀取到r0，然后將r0 對應的處理器模式為修改成未定

;義指令中止模式，再寫回狀態寄存器使處理器真正切換到未定義指令中止模式，這就

;是“讀出-修改-寫回”的方式來修改狀態寄存器的內容。最后將該模式的堆棧指針sp 指

; 向UndefStack 定義的地址，其他的模式操作方式也是一樣

orr r1,r0,#ABORTMODE|NOINT

msr cpsr_cxsf,r1 ;AbortMode

ldr sp,=AbortStack ; AbortStack=0x33FF_6000

orr r1,r0,#IRQMODE|NOINT

msr cpsr_cxsf,r1 ;IRQMode

ldr sp,=IRQStack ; IRQStack=0x33FF_7000

orr r1,r0,#FIQMODE|NOINT

msr cpsr_cxsf,r1 ;FIQMode

ldr sp,=FIQStack ; FIQStack=0x33FF_8000

bic r0,r0,#MODEMASK|NOINT

orr r1,r0,#SVCMODE

msr cpsr_cxsf,r1 ;SVCMode

ldr sp,=SVCStack ; SVCStack=0x33FF_5800

;USER mode has not be initialized.

mov pc,lr

;The LR register will not be valid if the current mode is not SVC mode.

LTORG

這段程序的開始使用DATA 偽操作指明SMRDATA 標號處作為一段數據，而非代碼。

接下來就用DCD 分配一個字的內存單元，一共13 個字?jǐn)?shù)據。

SMRDATA DATA

; Memory configuration should be optimized for best performance

; The following parameter is not optimized.

; Memory access cycle parameter strategy

; 1) The memory settings is safe parameters even at HCLK=75Mhz.

; 2) SDRAM refresh period is for HCLK<=75Mhz.

DCD (0+(B1_BWSCON<<4)+(B2_BWSCON<<8)+(B3_BWSCON<<12)+(B4_BWSCON<<16)+(B5_BWSCON<<20)+(B6_BWSCON<<24)+(B7_BWSCON<<28))

DCD ((B0_Tacs<<13)+(B0_Tcos<<11)+(B0_Tacc<<8)+(B0_Tcoh<<6)+(B0_Tah<<4)+(B0_Tacp<<2)+(B0_PMC)) ;GCS0

DCD ((B1_Tacs<<13)+(B1_Tcos<<11)+(B1_Tacc<<8)+(B1_Tcoh<<6)+(B1_Tah<<4)+(B1_Tacp<<2)+(B1_PMC)) ;GCS1

DCD ((B2_Tacs<<13)+(B2_Tcos<<11)+(B2_Tacc<<8)+(B2_Tcoh<<6)+(B2_Tah<<4)+(B2_Tacp<<2)+(B2_PMC)) ;GCS2

DCD ((B3_Tacs<<13)+(B3_Tcos<<11)+(B3_Tacc<<8)+(B3_Tcoh<<6)+(B3_Tah<<4)+(B3_Tacp<<2)+(B3_PMC)) ;GCS3

DCD ((B4_Tacs<<13)+(B4_Tcos<<11)+(B4_Tacc<<8)+(B4_Tcoh<<6)+(B4_Tah<<4)+(B4_Tacp<<2)+(B4_PMC)) ;GCS4

DCD ((B5_Tacs<<13)+(B5_Tcos<<11)+(B5_Tacc<<8)+(B5_Tcoh<<6)+(B5_Tah<<4)+(B5_Tacp<<2)+(B5_PMC)) ;GCS5

DCD ((B6_MT<<15)+(B6_Trcd<<2)+(B6_SCAN)) ;GCS6

DCD ((B7_MT<<15)+(B7_Trcd<<2)+(B7_SCAN)) ;GCS7

DCD ((REFEN<<23)+(TREFMD<<22)+(Trp<<20)+(Tsrc<<18)+(Tchr<<16)+REFCNT)

DCD 0x32 ;SCLK power saving mode, BANKSIZE 128M/128M

DCD 0x30 ;MRSR6 CL=3clk

DCD 0x30 ;MRSR7 CL=3clk

BaseOfROM DCD |Image$$RO$$Base|

TopOfROM DCD |Image$$RO$$Limit|

BaseOfBSS DCD |Image$$RW$$Base|

BaseOfZero DCD |Image$$ZI$$Base|

EndOfBSS DCD |Image$$ZI$$Limit|

ALIGN

;Function for entering power down mode

; 1. SDRAM should be in self-refresh mode.

; 2. All interrupt should be maksked for SDRAM/DRAM self-refresh.

; 3. LCD controller should be disabled for SDRAM/DRAM self-refresh.

; 4. The I-cache may have to be turned on.

; 5. The location of the following code may have not to be changed.

;void EnterPWDN(int CLKCON);

EnterPWDN

mov r2,r0 ;r2=rCLKCON

tst r0,#0x8 ;SLEEP mode?

bne ENTER_SLEEP

ENTER_STOP

ldr r0,=REFRESH

ldr r3,[r0] ;r3=rREFRESH

mov r1, r3

orr r1, r1, #BIT_SELFREFRESH

str r1, [r0] ;Enable SDRAM self-refresh

mov r1,#16 ;wait until self-refresh is issued. may not be needed.

0 subs r1,r1,#1

bne %B0

ldr r0,=CLKCON ;enter STOP mode.

str r2,[r0]

mov r1,#32

0 subs r1,r1,#1 ;1) wait until the STOP mode is in effect.

bne %B0 ;2) Or wait here until the CPU&Peripherals will be turned-off

; Entering SLEEP mode, only the reset by wake-up is available.

ldr r0,=REFRESH ;exit from SDRAM self refresh mode.

str r3,[r0]

MOV_PC_LR

ENTER_SLEEP

;NOTE.

;1) rGSTATUS3 should have the return address after wake-up from SLEEP mode.

ldr r0,=REFRESH

ldr r1,[r0] ;r1=rREFRESH

orr r1, r1, #BIT_SELFREFRESH

str r1, [r0] ;Enable SDRAM self-refresh

mov r1,#16 ;Wait until self-refresh is issued,which may not be needed.

0 subs r1,r1,#1

bne %B0

ldr r1,=MISCCR

ldr r0,[r1]

orr r0,r0,#(7<<17) ;Set SCLK0=0, SCLK1=0, SCKE=0.

str r0,[r1]

ldr r0,=CLKCON ; Enter sleep mode

str r2,[r0]

b . ;CPU will die here.

WAKEUP_SLEEP;從睡眠狀態醒過來

;Release SCLKn after wake-up from the SLEEP mode.

ldr r1,=MISCCR

ldr r0,[r1]

bic r0,r0,#(7<<17) ;SCLK0:0->SCLK, SCLK1:0->SCLK, SCKE:0->=SCKE.

str r0,[r1]

;Set memory control registers

ldr r0,=SMRDATA ;be careful!

ldr r1,=BWSCON ;BWSCON Address

add r2, r0, #52 ;End address of SMRDATA

0

ldr r3, [r0], #4

str r3, [r1], #4

cmp r2, r0

bne %B0

mov r1,#256

0 subs r1,r1,#1 ;1) wait until the SelfRefresh is released.

bne %B0

ldr r1,=GSTATUS3 ;GSTATUS3 has the start address just after SLEEP wake-up

ldr r0,[r1]

mov pc,r0