做個ADSL+LINUX軟路由器

作者：時間：2014-12-30 來源：網絡

加入技術交流群
- 掃碼加入
  和技術大咖面對面交流
  海量資料庫查詢

　　3、下一步做ADSL的驅動。去http://www.roaringpenguin.com/pppoe/rp-pppoe-2.6.tar.gz 下個驅動程序先，大概85K大小。考到/root去。

本文引用地址：http://m.butianyuan.cn/article/267508.htm

　　然后 #tar xvfz rp-pppoe-2.6.tar.gz

　　#cd rp-pppoe-2.6

　　#./go

　　開始安裝，裝好就#make一下下，開始配置ADSL。

　　Welcome to the Roaring Penguin ADSL client setup. First, I will run some checks on your system to make sure the PPPoE client is installed properly... Looks good! Now, please enter some information:

　　USER NAME

　　>>> Enter your PPPoE user name (default):

　　這里輸入在電信局申請的adsl的帳號

　　INTERFACE

　　>>> Enter the Ethernet interface connected to the ADSL modem For Solaris, this is likely to be something like /dev/hme0. For Linux, it will be ethn, where 'n' is a number.(default eth0):

　　問你用哪片網卡撥號，默認是第一片eth0就可以了

　　4、最后一步：配置ipchains偽裝IP。

　　在 /etc/sysconfig的network文件里保證要有這句： FORWARD_IPV4=true

　　然后改/etc/rc.d/rc.local這個文件，加入以下內容

　　Do you want the link to come up on demand, or stay up continuously? If you want it to come up on demand, enter the idle time in seconds after which the link should be dropped. If you want the link to stay up permanently, enter 'no' (two letters, lower-case.)

　　NOTE: Demand-activated links do not interact well with dynamic IP addresses. You may have some problems with demand-activated links.

　　>>> Enter the demand value (default no):

　　用缺省的no就可以了。

　　Please enter the IP address of your ISP's primary DNS server. If your ISP claims that 'the server will provide DNS addresses', enter 'server' (all lower-case) here. If you just press enter, I will assume you know what you are doing and not modify your DNS setup.

　　>>> Enter the DNS information here:

　　這里填你ISP的DNS地址，成都用61.139.2.69,輔助DNS成都可用202.98.127.32

　　PASSWORD

　　>>> Please enter your PPPoE password:

　　ADSL撥號密碼這個東東。

　　搞定!爽爽，用#adsl-start 就可以開始撥號。如果連接成功系統會提示你：…….connect

　　用ifconfig看看。[root@localhost /root]# ifconfig

　　eth0 Link encap:Ethernet HWaddr 00:40:05:64:11:28

　　inet addr:192.168.0.254 Bcast:192.168.0.255 Mask:255.255.255.0

　　UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1

　　RX packets:347573 errors:0 dropped:0 overruns:0 frame:0

　　TX packets:40194 errors:0 dropped:0 overruns:0 carrier:0