單片機鍵盤輸入及串口發送

typedef unsigned char uchar;
typedef unsigned int uint;

//數碼管端口控制
sbit SG = P0^0;//控制個位
sbit SS = P0^1;//控制十位
unsigned char code rst[6]={0xe4,0xc0,0xe0,0xc0,0xe0,0x22};//定義一個code類型 實現軟件復位
uchar tab0[] = {0x81,0xbd,0x92,0x98,0xac,0xc8,0xc0,0x9d,0x80,0x88}; //0~9共陽數碼管
uchar tab1[2] ={0xfe,0xfe} ;
uchar SendBuf[10];//發送的數
uchar *p;
uchar t1,t2;
uchar channel;
uchar SendLen=0,BufLen=7;
Timer_0();//數碼動態掃描的定時函數
Delay(uint t);//按鍵去抖的延時函數
uint Key_1();//鍵盤掃描函數
uint Key_2();//鍵盤返回值函數
Delay();//延時函數
Reset();//復位函數
Affirm();//確認發送函數
void init_ser1();//串口初始化函數
void SendTo();
void Coding(char,char,char,char,char);
main()
{
ucharn;
init_ser1();//串口初始化函數
P2=0x00;
P3=0x0f;
p=tab1;
Timer_0(); //定時器初始化函數
SendTo();
t1 = 0;
t2 = 0;
while(1)
{

n=Key_2();
if(n!=0xff)
{

//Led=0;
if(*p==0xfe)
{
if(p==tab1)
{
t1 = n;
}
else if(p==tab1+1)
{
t2 = n;
}
//Led=1;
Delay(9000); //特別關鍵的延時
//Led=0;

*p=tab0[n];
p++;
}
}

}
}
uint Key_1()
{
uint i,j;
if(P2!=0x00)
{
Delay(300);//去除按鍵抖動
if(P2!=0x00)
{
i=P2;
return(i);
}
}
if(P3!=0xf0)
{
Delay(300);
if(P3!=0xf0)

j=P3;
return(j);
}

}
uint Key_2()
{
switch(key_1()) //根據掃描結果選取值
{
case 0x01:return 1;break;
case0x02:return 2;break;
case0x04:return 3;break;
case0x08:return 4;break;
case0x10:return 5;break;
case0x20:return 6;break;
case0x40:return 7;break;
case0x80:return 8;break;
case0x1f:return 9;break;
case0x2f:Reset(); break;
case0x4f:return 0;break;
case0x8f:Affirm();break;
default:return 0xff;break;
}
}
Delay(uint t)//延時函數
{

while(--t);

}
Reset()//清除復位函數
{
Delay(20000);
Coding(0,0,0,0,0);
(*((void (*)())rst))();//復位
}
Affirm()//確認發送函數
{


Delay(20000);
channel = t1*10 + t2;
Coding(channel,0,0,0,0);
SendTo();

//flag=1;
}
Timer_0()//定時器0初始化
{
TMOD=TMOD&0xf0|0x01;
TR0=1;
ET0=1;
//EA=1;
}
interrupt_0() interrupt 1//數碼管掃描
{
TH0=0xf8;
TL0=0x30;

P1=tab1[0];
SG=1;
SS=0;
Delay(150);

P1=tab1[1];
SG=0;
SS=1;

}

void Coding(char CHANNEL,char Command3,char Command4,char Command5,char Command6)
{
SendBuf[0]=0xFF;
SendBuf[1]=CHANNEL;
SendBuf[2]=Command3;
SendBuf[3]=Command4;
SendBuf[4]=Command5;
SendBuf[5]=Command6;
SendBuf[6]=Command6+Command5+Command4+Command3+CHANNEL;
}

void init_ser1()
{

// REN=1;//允許串行口接收數據
//
// SM0=0;
// SM1=1;//串行口工作方式為1
//
// TMOD=TMOD&0xf0|0x20;//通過定時器1設置串口波特率
// PCON|=0x0;
// TH1=0xFD;
// TL1=0xFD; //波特率9600
// PS=1;
//
// TR1=1;//啟動定時器1
// ES=1;//開串行口中斷
// PS=1;
PCON=0X00;
SCON=0X50;
TMOD|=0X20;
TH1=0xFd;
TL1=0xFd;
TI=1;
EA=1;
TR1=1;
ES=1;
}
void Serial(void)interrupt 4
{
if(RI)
{
RI=0;
}
if(TI)
{
TI=0;
//Delay(20);
if(SendLen >= BufLen) BufLen = 0;
if(BufLen)
{
SBUF = SendBuf[SendLen++];
}
}
}
void SendTo(void)
{
BufLen = 7;
SendLen = 0;
SBUF = "" ;
do{}
while(BufLen);
}