51單片機利用LED宏，控制LED等的亮度

經常用led燈來觀察現象,甚至調試代碼,修改代碼時用0和1很不方便,而且閱讀性也不好,利用個宏,用起來方便些。

今天嘗試控制燈的亮度. 先試試for循環控制,占空比調節...

c代碼

//#include my51.h

#include

typedef unsigned char u8;

typedef unsigned short int u16;

#ifndef _51LED_

#define _51LED_

#define led P1 //P1總線連8個led燈,燈連573鎖存器,P1置低電平點亮

#define LED led

#define ON(x) P1(~(1(x))) //打開某個燈,開多個燈用 ON(m) ON(n)

#define OFF(x) P1|(1(x)) //關閉某個燈,關多個燈用 OFF(m)| OFF(n)

#define on(x) ON(x) //包含大小寫

#define off(x) OFF(x)

#define ledon 0 //某個燈,打開

#define ledoff 1 //某個燈,關閉

sbit led0=P1^0;

sbit led1=P1^1;

sbit led2=P1^2;

sbit led3=P1^3;

sbit led4=P1^4;

sbit led5=P1^5;

sbit led6=P1^6;

sbit led7=P1^7;

sbit ledLock=P2^5; //鎖定當前8個led的狀態,0鎖定 ,1不鎖定

#endif

void ledCtr(u8 ledX,u8 per) //參數1是某個燈,參數2是亮度

{

u8 i=1;

for(i=1;i=100;i++)

{

if(i

{

led=on(ledX) ; //打開燈

}

else

{

led=off(ledX); //關閉燈

}

}

}

void delayms(u16 ms) //毫秒級軟延時函數

{

u16 i,j;

for(i=ms;i>0;i--)

{

for(j=113;j>0;j--)

{}

}

}

void main() //測試

{

led6=ledon; //打開6號燈,亮度100%

led=on(0); //打開0號燈,亮度100%

led=on(1) on(5); //打開1號和5號燈,亮度100%

delayms(2000);

led0=ledoff; //關閉0號燈

led=off(6)|off(1)|off(5);//關閉1,5,6號燈

while(1)

{

ledCtr(2,5); //僅打開2號燈,亮度5%, 省電...

}

}