STM32 延時函數封裝
/*---------------------------------
本文引用地址:http://m.butianyuan.cn/article/148436.htm說明:只需在工程中加入delay.c和delay.h
文件,即可用 Delayms(__IO uint32_t nTime);
Delayus(__IO uint32_t nTime)
-----------------------------------*/
#ifndef __DELAY_H
#define __DELAY_H
#include stm32f10x.h
/*---------------------------------
描 述:參數1即為1ms,1000即為1s;只有幾
us的誤差;
-----------------------------------*/
extern void Delayms(__IO uint32_t nTime);
/*---------------------------------
描 述:參數1即為1us,1000即為1ms;只有幾
us的誤差;
-----------------------------------*/
extern void Delayus(__IO uint32_t nTime);
/*---------------------------------
函數名:延時調整形式的delaynus函數,
描 述:參數1即為1us,1000即為1ms;
-----------------------------------*/
extern void delay_nus(unsigned long n);
/*---------------------------------
函數名:延時調整形式的delaynms函數,
描 述:參數1即為1ms,1000即為1s;
-----------------------------------*/
extern void delay_nms(unsigned long n);
#endif
C 函數
/*---------------------------------
延時模塊函數
說明:只需在工程中加入delay.c和delay.h
文件,即可用 Delayms(__IO uint32_t nTime);
Delayus(__IO uint32_t nTime)
-----------------------------------*/
#includedelay.h
static __IO uint32_t TimingDelay;
/* Private function prototypes -----------------------------------------------*/
/*---------------------------------
函數名:ms延時函數
描 述:參數1即為1ms,1000即為1s;只有幾
us的誤差;
-----------------------------------*/
void Delayms(__IO uint32_t nTime)
{
while(SysTick_Config(SystemCoreClock/1000));
TimingDelay = nTime;
while(TimingDelay != 0);
SysTick->CTRL=0x00; //關閉計數器
SysTick->VAL =0X00; //清空計數器
}
/*---------------------------------
函數名:us延時函數
描 述:參數1即為1us,1000即為1ms;只有幾
us的誤差;
-----------------------------------*/
void Delayus(__IO uint32_t nTime)
{
while(SysTick_Config(SystemCoreClock/1000000));
TimingDelay = nTime;
while(TimingDelay != 0);
SysTick->CTRL=0x00; //關閉計數器
SysTick->VAL =0X00; //清空計數器
}
/*---------------------------------
函數名:延時輔助函數
描 述:
-----------------------------------*/
void TimingDelay_Decrement(void)
{
if (TimingDelay != 0x00)
{
TimingDelay--;
}
}
/*---------------------------------
函數名:systick的中斷函數
描 述:參數1即為1us,1000即為1ms;只有幾
us的誤差;
-----------------------------------*/
void SysTick_Handler(void)
{
TimingDelay_Decrement();
}
/*---------------------------------
函數名:延時調整形式的delaynus函數,
描 述:參數1即為1us,1000即為1ms;
-----------------------------------*/
void delay_nus(unsigned long n)
{
unsigned long j;
while(n--)
{
j=12;
while(j--);
}
}
/*---------------------------------
函數名:延時調整形式的delaynms函數,
描 述:參數1即為1ms,1000即為1s;
-----------------------------------*/
void delay_nms(unsigned long n)
{
while(n--)
delay_nus(1030);
}
評論