新聞中心

EEPW首頁 > 手機與無線通信 > 學習方法與實踐 > Linux系統如何通過手機GPRS功能無線上網

Linux系統如何通過手機GPRS功能無線上網

作者:korn 時間:2008-01-29 來源:賽迪網 收藏


本文引用地址:http://m.butianyuan.cn/article/78201.htm

      首先,要有一臺具備GPRS且?guī)в衜odem功能的手機,以下以palm treo 650為例。

       650是不帶modem功能,要通過軟件實現,下載 USB modem軟件并安裝在650上。該軟件支持藍牙和usb數據線兩種模式!

       下面首先看系統是否能檢測到modem


sudo wvdialconf



Editing `/etc/wvdial.conf'.
            Scanning your serial ports for a modem.
            Modem Port Scan<*1>: S0 S1 S2 S3
            WvModem<*1>: Cannot get information for serial port.
            ttyACM0<*1>: ATQ0 V1 E1 -- OK
            ttyACM0<*1>: ATQ0 V1 E1 Z -- OK
            ttyACM0<*1>: ATQ0 V1 E1 S0=0 -- OK
            ttyACM0<*1>: ATQ0 V1 E1 S0=0 &C1 -- OK
            ttyACM0<*1>: ATQ0 V1 E1 S0=0 &C1 &D2 -- OK
            ttyACM0<*1>: ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0 -- OK
            ttyACM0<*1>: Modem Identifier: ATI -- ENZO
            ttyACM0<*1>: Speed 4800: AT -- OK
            ttyACM0<*1>: Speed 9600: AT -- OK
            ttyACM0<*1>: Speed 19200: AT -- OK
            ttyACM0<*1>: Speed 38400: AT -- OK
            ttyACM0<*1>: Speed 57600: AT -- OK
            ttyACM0<*1>: Speed 115200: AT -- OK
            ttyACM0<*1>: Speed 230400: AT -- OK
            ttyACM0<*1>: Speed 460800: AT -- OK
            ttyACM0<*1>: Max speed is 460800; that should be safe.
            ttyACM0<*1>: ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0 -- OK
            Found an USB modem on /dev/ttyACM0.
            Modem configuration written to /etc/wvdial.conf.
            ttyACM0: Speed 460800; init "ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0"


      如果出現以下信息則能檢測modem且將配置自動寫入 /etc/wvdial.conf文件。你modem的設備文件為/dev/ttyACM0

      由于配置文件為普通撥號而建立,所以不適合grps撥號,要作以下修改


[Dialer defaults]
            Init1 = at+cgdcont=1,"ip","cmwap"
            Modem Type = USB Modem
            ISDN = 0
            Phone = *99***1#
            Modem = /dev/ttyACM0
            Username = any
            Carrier Check = no
            Password = any
            Baud = 460800


       保存后,使用wvdial撥號


sudo wvdial

       使用超級用戶操作,不然無法會提示設備忙,或更改用戶權限。



--> WvDial: Internet dialer version 1.60
            --> Cannot get information for serial port.
            --> Initializing modem.
            --> Sending: at+cgdcont=1,"ip","cmwap"
            at+cgdcont=1,"ip","cmwap"
            OK
            --> Modem initialized.
            --> Sending: ATDT*99***1#
            --> Waiting for carrier.
            ATDT*99***1#
            CONNECT
            ~[7f]}#@!}![06]} }<}!}$}%}"}&} } } } }#}$@#}%}&}$^[7f]o}'}"}(}"Q}+~
            --> Carrier detected. Waiting for prompt.
            ~[7f]}#@!}![06]} }<}!}$}%}"}&} } } } }#}$@#}%}&}$^[7f]o}'}"}(}"Q}+~
            --> PPP negotiation detected.
            --> Starting pppd at Sat Jan 19 10:56:20 2008
            --> Pid of pppd: 6967
            --> Using interface ppp0
            --> pppd: (m[07][08]hr[07][08]
            --> pppd: (m[07][08]hr[07][08]
            --> pppd: (m[07][08]hr[07][08]
            --> pppd: (m[07][08]hr[07][08]
            --> pppd: (m[07][08]hr[07][08]
            --> local IP address 10.216.91.90
            --> pppd: (m[07][08]hr[07][08]
            --> remote IP address 10.216.91.0
            --> pppd: (m[07][08]hr[07][08]

     到如已經成功啦!我們?cè)賮?lái)看看路由表



$ route
            Kernel IP routing table
            Destination Gateway Genmask Flags Metric Ref Use Iface
            10.216.91.0 * 255.255.255.255 UH 0 0 0 ppp0
            192.168.0.0 * 255.255.255.0 U 0 0 0 wlan0
            default 192.168.0.1 0.0.0.0 UG 0 0 0 wlan0

        因?yàn)槲疫@里還連接到無線網絡,所以默認網關是 192.168.0.1,如果只有GPRS撥號連接,則信息會是:



$ route
            Kernel IP routing table
            Destination Gateway Genmask Flags Metric Ref Use Iface
            10.216.91.0 * 255.255.255.255 UH 0 0 0 ppp0
            default 10.216.91.90 0.0.0.0 UG 0 0 0 ppp0

      此時,只需設置代理即可以上網了 代理為 10.0.0.172:80


      由于移動限制了瀏覽器,必須要將瀏覽器頭信息更改才能正常上網。不過已經可以上Q。MSN等聊天工具啦!!

linux操作系統文章專題:linux操作系統詳解(linux不再難懂)

linux操作系統文章專題:linux操作系統詳解(linux不再難懂)


評論


相關推薦

技術專區

關閉